From: Howcast on Fri, May 01 2009 9:13 PM

Another machining process by John @ Costa Mesa R&D Automotive Machine, this time its a Ford 460 intake manifold. www.engine-machining.com (949) 631-6376 Author: youtube

From: Howcast on Fri, May 01 2009 9:13 PM

Watch as John @ Costa Mesa R&D Automotive Machine modifies a BMW cylinder head for high performance springs and Ti retainers. www.engine-machining.com Author: youtube

From: Howcast on Fri, May 01 2009 9:13 PM

John Edwards 1968 Fiat 850 Sedan @ Qualcomm, run #4.www.engine-machining.com Author: youtube

From: Howcast on Fri, May 01 2009 9:13 PM

Here’s my killer guacamole recipe, it's simple and fast to make. It just doesn't get any better than this let me tell'ya. There's a lot more to Costa Mesa R&D Automotive Machine than great engine work. More to follow... www.Engine-Machining.com Author: youtube

From: Howcast on Fri, May 01 2009 8:38 PM

John @ Costa Mesa R&D Automotive Machine describes how to replace valve guides on the popular small block Chevrolet cylinder head. www.engine-machining.com Author: youtube

From: Howcast on Fri, May 01 2009 8:28 PM

A couple of home made buggies on the chassis dyno for tuning. The Lexus TT was tuned to get an additional 100 hp. Author: youtube

From: Howcast on Fri, May 01 2009 8:28 PM

John Edwards discusses the various types of connecting rods found in modern engines. Author: youtube

From: Howcast on Fri, May 01 2009 8:27 PM

Watch as John Edwards @ Costa Mesa R&D Automotive Maachine as he machines an air cooled 911 cylinder head.www.engine-machining.com949-631-6376 Author: youtube

From: Howcast on Fri, May 01 2009 8:27 PM

A pretty boring video about flywheel resurfacing... Hey, what can you say about flywheels, slap’em on the machine, turn it on, stand back and watch the sparks. Another John Edwards educational video stream. Author: youtube

From: Howcast on Fri, May 01 2009 8:23 PM

This is a 383 Chevy stroker motor that was going into an off-road pre-runner, here it is getting a low-stress break-in on my Simtester. The engine runs for about 40 minutes as I will typically see a 2-4 amp decrease in drive motor amperage and a 2-5 rpm increase. Both of the Au...

From: Howcast on Fri, May 01 2009 8:21 PM

John Edwards @ Costa Mesa R&D Automotive Machine uses the Zyglo penetrant method to test a Jeep crankshaft for cracks. Author: youtube

From: Howcast on Fri, May 01 2009 8:21 PM

John Edwards @ Costa Mesa R&D Automotive Machine demonstrates non destructive testing (NDT) magnetic particle inspection (Magnaflux) on a 460 Ford cylinder head to determine if the head is cracked. Author: youtube

From: Howcast on Fri, May 01 2009 8:21 PM

This video will show some of the modifications that are made by John Edwards @ Costa Mesa R&D Automotive Machine on a 1500cc Fiat X1/9 (Punto Marea) connecting rods and new forged JE pistons. Author: youtube

From: Howcast on Fri, May 01 2009 8:18 PM

John Edwards honing a Harley Davidson cylinder barrel on the Sunnen CV-616 cylinder king hone by @ Costa Mesa R&D Automotive Machine, (949) 631-6376.costamesardauto@sbcglobal.net Author: youtube

From: Howcast on Fri, May 01 2009 8:18 PM

Watch as John Edwards @ Costa Mesa R&D Automotive Machine addresses a common problem found with water cooled 911 and Boxter engines. Author: youtube

From: Howcast on Fri, May 01 2009 8:17 PM

The number don’t lie, we have a new CNC porting profile for the WRX Subaru cylinder heads. The intakes went from 236cfm to 280cfm! The exuaust from 165cfm/156cfm (straight port/dog-leg port) to 185cfm/195cfm. For more info about this new performance oriented service, call Jo Au...

From: Howcast on Fri, May 01 2009 8:14 PM

John gives you an inside look at how he installs the middle piston pin on the Subaru SVX flat-6 engine at Costa Mesa R&D Automotive Machine. www.engine-machining.com (949) 631-6376 Author: youtube

From: Howcast on Fri, May 01 2009 8:14 PM

This video demonstrates the Sunnen Thermal Cleaning system that was used to clean a small block (SBC) Chevrolet engine block by John Edwards @ Costa Mesa R&D Automotive Machine (949) 631-6376. Your comments appreciated! Author: youtube

From: Howcast on Fri, May 01 2009 8:13 PM

John Edwards demonstrates how to do a quick & easy valve adjustment on the Fiat 850 engine, same as would be for the 600 and Abarth 750/850/1000/1050 engines.www.Engine-Machining.com Author: youtube

From: Howcast on Fri, May 01 2009 8:13 PM

John Edwards demonstrates how to install cam bearings in a 428 Ford engine for a Shelby GT500K @ Costa Mesa R&D Automotive Machine, call(949) 631-6376 for more info. Author: youtube